2009/09/07

Cheapest & Latest ISO Standard (PDF) (8)

Any question, send the mail to findstandards@tom.com directly

http://www.findstandards.info

http://www.findstandards.info/Standards/DIN%20Standards.htm

http://www.findstandards.info/Standards/BSI%20Standards.htm

http://www.findstandards.info/Standards/ASTM%20Standards.htm

http://www.findstandards.info/Standards/ISO%20Standards.htm

http://www.findstandards.info/Standards/SAE%20Standards.htm

http://www.findstandards.info/Standards/JIS%20Standards.htm


http://www.findstandards.info/Standards/NFPA%20Standards.htm


http://www.findstandards.info/Standards/IEEE%20Standards.htm


http://www.findstandards.info/Standards/API%20Standards.htm


21 Mechanical systems and components for general use
ICS Field
21.020 Characteristics and design of machines, apparatus, equipment
Including reliability, dependability, maintainability, durability, etc.
Safety of machinery, see 13.110
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 3952-1:1981
Kinematic diagrams -- Graphical symbols 90.93 TC 10/SC 6
ISO 3952-1:1981/Amd 1:2002
60.60 TC 10/SC 6
ISO 3952-2:1981
Kinematic diagrams -- Graphical symbols 90.93 TC 10/SC 6
ISO 3952-3:1979
Kinematic diagrams -- Graphical symbols 90.93 TC 10/SC 6
ISO 3952-4:1984
Kinematic diagrams -- Graphical symbols 90.93 TC 10/SC 6
ISO 4871:1996
Acoustics -- Declaration and verification of noise emission values of machinery and equipment 90.92 TC 43/SC 1
ISO 10816-3:2009
Mechanical vibration -- Evaluation of machine vibration by measurements on non-rotating parts -- Part 3: Industrial machines with nominal power above 15 kW and nominal speeds between 120 r/min and 15 000 r/min when measured in situ 60.60 TC 108/SC 2
ISO/TR 11688-1:1995
Acoustics -- Recommended practice for the design of low-noise machinery and equipment -- Part 1: Planning 90.20 TC 43/SC 1
ISO/TR 11688-2:1998
Acoustics -- Recommended practice for the design of low-noise machinery and equipment -- Part 2: Introduction to the physics of low-noise design 90.20 TC 43/SC 1

21.040 Screw threads
Screw threads for aerospace construction, see 49.030.10
ICS Field
21.040.01 Screw threads in general
21.040.10 Metric screw threads
21.040.20 Inch screw threads
Including Whitworth screw threads
Pipe threads, see 21.040.30
21.040.30 Special screw threads
Including miniature screw threads, pipe threads, etc.


21.060 Fasteners
Fasteners for aerospace construction, see 49.030
Fasteners related to surgery, prosthetics and orthotics, see 11.040.40
21.080 Hinges, eyelets and other articulated joints
ICS Field
21.060.01 Fasteners in general
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 272:1982
Fasteners -- Hexagon products -- Widths across flats 90.93 TC 2/SC 7
ISO 273:1979
Fasteners -- Clearance holes for bolts and screws 90.20 TC 2/SC 7
ISO 1891:2009
Fasteners -- Terminology 90.92 TC 2/SC 7
ISO 3269:2000
Fasteners -- Acceptance inspection 90.93 TC 2/SC 7
ISO 3508:1976
Thread run-outs for fasteners with thread in accordance with ISO 261 and ISO 262 90.93 TC 2/SC 7
ISO 3800:1993
Threaded fasteners -- Axial load fatigue testing -- Test methods and evaluation of results 90.93 TC 2/SC 1
ISO 4042:1999
Fasteners -- Electroplated coatings 90.93 TC 2/SC 1
ISO 4753:1999
Fasteners -- Ends of parts with external ISO metric thread 90.20 TC 2/SC 7
ISO 4755:1983
Fasteners -- Thread undercuts for external metric ISO threads 90.93 TC 2/SC 7
ISO 5845-1:1995
Technical drawings -- Simplified representation of the assembly of parts with fasteners -- Part 1: General principles 90.20 TC 10/SC 6
ISO 8991:1986
Designation system for fasteners 90.93 TC 2/SC 7
ISO 10683:2000
Fasteners -- Non-electrolytically applied zinc flake coatings 90.93 TC 2/SC 1
ISO 10684:2004
Fasteners -- Hot dip galvanized coatings 90.93 TC 2/SC 1
ISO 10684:2004/Cor 1:2008
60.60 TC 2/SC 1
ISO 15330:1999
Fasteners -- Preloading test for the detection of hydrogen embrittlement -- Parallel bearing surface method 90.93 TC 2/SC 1
ISO 16047:2005
Fasteners -- Torque/clamp force testing 90.92 TC 2/SC 1
ISO 16048:2003
Passivation of corrosion-resistant stainless-steel fasteners 90.93 TC 2/SC 1
ISO 16426:2002
Fasteners -- Quality assurance system 90.93 TC 2/SC 7

21.060.10 Bolts, screws, studs
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO/DIS 225
Fasteners -- Bolts, screws, studs and nuts -- Symbols and designations of dimensions 40.20 TC 2/SC 7
ISO 225:1983
Fasteners -- Bolts, screws, studs and nuts -- Symbols and designations of dimensions 90.92 TC 2/SC 7
ISO 885:2000
General purpose bolts and screws -- Metric series -- Radii under the head 90.93 TC 2/SC 7
ISO 888:1976
Bolts, screws and studs -- Nominal lengths, and thread lengths for general purpose bolts 90.92 TC 2/SC 7
ISO/NP 888
Bolts, screws and studs -- Nominal lengths, and thread lengths for general purpose bolts 10.99 TC 2/SC 7
ISO 898-1:2009
Mechanical properties of fasteners made of carbon steel and alloy steel -- Part 1: Bolts, screws and studs with specified property classes -- Coarse thread and fine pitch thread 60.60 TC 2/SC 1
ISO 898-5:1998
Mechanical properties of fasteners made of carbon steel and alloy steel -- Part 5: Set screws and similar threaded fasteners not under tensile stresses 90.92 TC 2/SC 1
ISO 898-7:1992
Mechanical properties of fasteners -- Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 90.92 TC 2/SC 1
ISO 1207:1992
Slotted cheese head screws -- Product grade A 90.92 TC 2/SC 10
ISO 1479:1983
Hexagon head tapping screws 90.92 TC 2/SC 10
ISO 1481:1983
Slotted pan head tapping screws 90.92 TC 2/SC 10
ISO 1482:1983
Slotted countersunk (flat) head tapping screws (common head style) 90.92 TC 2/SC 10
ISO 1483:1983
Slotted raised countersunk (oval) head tapping screws (common head style) 90.92 TC 2/SC 10
ISO 1580:1994
Slotted pan head screws -- Product grade A 90.93 TC 2/SC 10
ISO 2009:1994
Slotted countersunk flat head screws (common head style) -- Product grade A 90.93 TC 2/SC 10
ISO 2010:1994
Countersunk slotted raised head screws (common head style) -- Product grade A 90.93 TC 2/SC 10
ISO 2342:2003
Slotted headless screws with shank 90.93 TC 2/SC 10
ISO 2702:1992
Heat-treated steel tapping screws -- Mechanical properties 90.92 TC 2/SC 10
ISO 3506-1:1997
Mechanical properties of corrosion-resistant stainless steel fasteners -- Part 1: Bolts, screws and studs 90.92 TC 2/SC 1
ISO/FDIS 3506-1
Mechanical properties of corrosion-resistant stainless steel fasteners -- Part 1: Bolts, screws and studs 50.00 TC 2/SC 1
ISO/FDIS 3506-3
Mechanical properties of corrosion-resistant stainless steel fasteners -- Part 3: Set screws and similar fasteners not under tensile stress 50.00 TC 2/SC 1
ISO 3506-3:1997
Mechanical properties of corrosion-resistant stainless-steel fasteners -- Part 3: Set screws and similar fasteners not under tensile stress 90.92 TC 2/SC 1
ISO/FDIS 3506-4
Mechanical properties of corrosion-resistant stainless steel fasteners -- Part 4: Tapping screws 50.00 TC 2/SC 1
ISO 3506-4:2003
Mechanical properties of corrosion-resistant stainless-steel fasteners -- Part 4: Tapping screws 90.92 TC 2/SC 1
ISO 4014:1999
Hexagon head bolts -- Product grades A and B 90.20 TC 2/SC 10
ISO 4015:1979
Hexagon head bolts -- Product grade B -- Reduced shank (shank diameter approximately equal to pitch diameter) 90.93 TC 2/SC 10
ISO 4016:1999
Hexagon head bolts -- Product grade C 90.20 TC 2/SC 10
ISO 4017:1999
Hexagon head screws -- Product grades A and B 90.20 TC 2/SC 10
ISO 4018:1999
Hexagon head screws -- Product grade C 90.20 TC 2/SC 10
ISO 4026:2003
Hexagon socket set screws with flat point 90.93 TC 2/SC 10
ISO 4027:2003
Hexagon socket set screws with cone point 90.93 TC 2/SC 10
ISO 4028:2003
Hexagon socket set screws with dog point 90.93 TC 2/SC 10
ISO 4029:2003
Hexagon socket set screws with cup point 90.93 TC 2/SC 10
ISO 4162:1990
Hexagon flange bolts -- Small series 90.93 TC 2/SC 10
ISO 4757:1983
Cross recesses for screws 90.60 TC 2/SC 10
ISO 4759-1:2000
Tolerances for fasteners -- Part 1: Bolts, screws, studs and nuts -- Product grades A, B and C 90.93 TC 2/SC 7
ISO 4762:2004
Hexagon socket head cap screws 90.93 TC 2/SC 10
ISO 4766:1983
Slotted set screws with flat point 90.92 TC 2/SC 10
ISO 6157-1:1988
Fasteners -- Surface discontinuities -- Part 1: Bolts, screws and studs for general requirements 90.93 TC 2/SC 7
ISO 6157-3:1988
Fasteners -- Surface discontinuities -- Part 3: Bolts, screws and studs for special requirements 90.93 TC 2/SC 7
ISO 7045:1994
Pan head screws with type H or type Z cross recess -- Product grade A 90.93 TC 2/SC 10
ISO 7046-1:1994
Countersunk flat head screws (common head style) with type H or type Z cross recess -- Product grade A -- Part 1: Steel of property class 4.8 90.93 TC 2/SC 10
ISO 7046-2:1990
Cross-recessed countersunk flat head screws (common head style) -- Grade A -- Part 2: Steel of property class 8.8, stainless steel and non-ferrous metals 90.93 TC 2/SC 10
ISO 7047:1994
Countersunk raised head screws (common head style) with type H or type Z cross recess -- Product grade A 90.93 TC 2/SC 10
ISO 7048:1998
Cross recessed cheese head screws 90.93 TC 2/SC 10
ISO 7049:1983
Cross recessed pan head tapping screws 90.92 TC 2/SC 10
ISO 7050:1983
Cross recessed countersunk (flat) head tapping screws (common head style) 90.92 TC 2/SC 10
ISO 7051:1983
Cross recessed raised countersunk (oval) head tapping screws 90.92 TC 2/SC 10
ISO 7053:1992
Hexagon washer head tapping screws 90.92 TC 2/SC 10
ISO 7085:1999
Mechanical and performance requirements of case hardened and tempered metric thread rolling screws 95.20 TC 2/SC 1
ISO 7378:1983
Fasteners -- Bolts, screws and studs -- Split pin holes and wire holes 90.93 TC 2/SC 7
ISO 7379:1983
Hexagon socket head shoulder screws 90.93 TC 2/SC 10
ISO 7380:2004
Hexagon socket button head screws 90.92 TC 2/SC 10
ISO/CD 7380-1
Hexagon socket button head screws -- Part 1: Button head (head shape A) 30.20 TC 2/SC 10
ISO/CD 7380-2
Hexagon socket button head screws -- Part 2: Button head with collar (head shape B) 30.20 TC 2/SC 10
ISO 7434:1983
Slotted set screws with cone point 90.20 TC 2/SC 10
ISO 7435:1983
Slotted set screws with long dog point 90.20 TC 2/SC 10
ISO 7436:1983
Slotted set screws with cup point 90.20 TC 2/SC 10
ISO 7721:1983
Countersunk head screws -- Head configuration and gauging 90.20 TC 2/SC 10
ISO 7721-2:1990
Countersunk flat head screws -- Part 2: Penetration depth of cross recesses 90.20 TC 2/SC 10
ISO 8676:1999
Hexagon head screws with metric fine pitch thread -- Product grades A and B 90.20 TC 2/SC 10
ISO 8678:1988
Cup head square neck bolts with small head and short neck -- Product grade B 90.93 TC 2/SC 10
ISO 8765:1999
Hexagon head bolts with metric fine pitch thread -- Product grades A and B 90.20 TC 2/SC 10
ISO 8839:1986
Mechanical properties of fasteners -- Bolts, screws, studs and nuts made of non-ferrous metals 90.92 TC 2/SC 1
ISO 8992:2005
Fasteners -- General requirements for bolts, screws, studs and nuts 90.93 TC 2/SC 7
ISO 10509:1992
Hexagon flange head tapping screws 90.60 TC 2/SC 10
ISO 10510:1999
Tapping screw and washer assemblies with plain washers 90.20 TC 2/SC 10
ISO 10642:2004
Hexagon socket countersunk head screws 90.93 TC 2/SC 10
ISO 10664:2005
Hexalobular internal driving feature for bolts and screws 90.93 TC 2/SC 10
ISO 10666:1999
Drilling screws with tapping screw thread -- Mechanical and functional properties 90.20 TC 2/SC 10
ISO/CD 12474
Hexagon socket head cap screws with metric fine pitch thread 30.99 TC 2/SC 10
ISO 13918:2008
Welding -- Studs and ceramic ferrules for arc stud welding 60.60 TC 44/SC 10
ISO 14579:2001
Hexalobular socket head cap screws 90.93 TC 2/SC 10
ISO 14580:2001
Hexalobular socket cheese head screws 90.93 TC 2/SC 10
ISO 14580:2001/Cor 1:2004
60.60 TC 2/SC 10
ISO 14583:2001
Hexalobular socket pan head screws 90.93 TC 2/SC 10
ISO 14583:2001/Cor 1:2004
60.60 TC 2/SC 10
ISO 14584:2001
Hexalobular socket raised countersunk head screws 90.93 TC 2/SC 10
ISO 14585:2001
Hexalobular socket pan head tapping screws 90.93 TC 2/SC 10
ISO 14585:2001/Cor 1:2004
60.60 TC 2/SC 10
ISO 14586:2001
Hexalobular socket countersunk head tapping screws 90.93 TC 2/SC 10
ISO 14587:2001
Hexalobular socket raised countersunk (oval) head tapping screws 90.93 TC 2/SC 10
ISO 15065:2005
Countersinks for countersunk head screws with head configuration in accordance with ISO 7721 90.93 TC 2/SC 7
ISO 15071:1999
Hexagon bolts with flange -- Small series -- Product grade A 90.20 TC 2/SC 10
ISO 15071:1999/Cor 1:2006
60.60 TC 2/SC 10
ISO 15072:1999
Hexagon bolts with flange with metric fine pitch thread -- Small series -- Product grade A 90.20 TC 2/SC 10
ISO 15072:1999/Cor 1:2006
60.60 TC 2/SC 10
ISO 15480:1999
Hexagon washer head drilling screws with tapping screw thread 90.20 TC 2/SC 10
ISO 15481:1999
Cross recessed pan head drilling screws with tapping screw thread 90.20 TC 2/SC 10
ISO 15482:1999
Cross recessed countersunk head drilling screws with tapping screw thread 90.20 TC 2/SC 10
ISO 15483:1999
Cross recessed raised countersunk head drilling screws with tapping screw thread 90.20 TC 2/SC 10
ISO 23429:2004
Gauging of hexagon sockets 90.93 TC 2/SC 10

21.060.20 Nuts
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO/NP 898-2
Mechanical properties of fasteners -- Part 2: Nuts with specified proof load values -- Coarse thread 10.99 TC 2/SC 1
ISO 898-2:1992
Mechanical properties of fasteners -- Part 2: Nuts with specified proof load values -- Coarse thread 90.92 TC 2/SC 1
ISO 898-6:1994
Mechanical properties of fasteners -- Part 6: Nuts with specified proof load values -- Fine pitch thread 90.92 TC 2/SC 1
ISO/NP 898-6
Mechanical properties of fasteners -- Part 6: Nuts with specified proof load values -- Fine pitch thread 10.99 TC 2/SC 1
ISO 2320:2008
Prevailing torque type steel nuts -- Mechanical and performance properties 60.60 TC 2/SC 1
ISO 3506-2:1997
Mechanical properties of corrosion-resistant stainless-steel fasteners -- Part 2: Nuts 90.92 TC 2/SC 1
ISO/FDIS 3506-2
Mechanical properties of corrosion-resistant stainless steel fasteners -- Part 2: Nuts 50.00 TC 2/SC 1
ISO 4032:1999
Hexagon nuts, style 1 -- Product grades A and B 90.20 TC 2/SC 10
ISO 4033:1999
Hexagon nuts, style 2 -- Product grades A and B 90.20 TC 2/SC 10
ISO 4034:1999
Hexagon nuts -- Product grade C 90.20 TC 2/SC 10
ISO 4035:1999
Hexagon thin nuts (chamfered) -- Product grades A and B 90.20 TC 2/SC 10
ISO 4036:1999
Hexagon thin nuts (unchamfered) -- Product grade B 90.20 TC 2/SC 10
ISO 4161:1999
Hexagon nuts with flange -- Coarse thread 90.20 TC 2/SC 10
ISO 4759-1:2000
Tolerances for fasteners -- Part 1: Bolts, screws, studs and nuts -- Product grades A, B and C 90.93 TC 2/SC 7
ISO 6157-2:1995
Fasteners -- Surface discontinuities -- Part 2: Nuts 90.93 TC 2/SC 7
ISO 7040:1997
Prevailing torque type hexagon nuts (with non-metallic insert), style 1 -- Property classes 5, 8 and 10 90.60 TC 2/SC 10
ISO 7041:2002
Prevailing torque type hexagon nuts (with non-metallic insert), style 2 -- Property classes 9 and 12 90.60 TC 2/SC 10
ISO 7042:1997
Prevailing torque type all-metal hexagon nuts, style 2 -- Property classes 5, 8, 10 and 12 90.60 TC 2/SC 10
ISO 7043:1997
Prevailing torque type hexagon nuts with flange (with non-metallic insert) -- Product grades A and B 90.60 TC 2/SC 10
ISO 7044:1997
Prevailing torque type all-metal hexagon nuts with flange -- Product grades A and B 90.60 TC 2/SC 10
ISO 7719:1997
Prevailing torque type all-metal hexagon nuts, style 1 -- Property classes 5, 8 and 10 90.60 TC 2/SC 10
ISO 7720:1997
Prevailing torque type all-metal hexagon nuts, style 2 -- Property class 9 90.60 TC 2/SC 10
ISO 8673:1999
Hexagon nuts, style 1, with metric fine pitch thread -- Product grades A and B 90.20 TC 2/SC 10
ISO 8674:1999
Hexagon nuts, style 2, with metric fine pitch thread -- Product grades A and B 90.20 TC 2/SC 10
ISO 8675:1999
Hexagon thin nuts (chamfered) with metric fine pitch thread -- Product grades A and B 90.20 TC 2/SC 10
ISO 8839:1986
Mechanical properties of fasteners -- Bolts, screws, studs and nuts made of non-ferrous metals 90.92 TC 2/SC 1
ISO 8992:2005
Fasteners -- General requirements for bolts, screws, studs and nuts 90.93 TC 2/SC 7
ISO 10484:1997
Widening test on nuts 90.93 TC 2/SC 1
ISO 10485:1991
Cone proof load test on nuts 90.93 TC 2/SC 1
ISO 10511:1997
Prevailing torque type hexagon thin nuts (with non-metallic insert) 90.60 TC 2/SC 10
ISO 10512:1997
Prevailing torque type hexagon nuts (with non-metallic insert), style 1, with metric fine pitch thread -- Property classes 6, 8 and 10 90.60 TC 2/SC 10
ISO 10513:1997
Prevailing torque type all-metal hexagon nuts, style 2, with metric fine pitch thread -- Property classes 8, 10 and 12 90.60 TC 2/SC 10
ISO 10663:1999
Hexagon nuts with flange -- Fine pitch thread 90.20 TC 2/SC 10
ISO 12125:1997
Prevailing torque type hexagon nuts with flange (with non-metallic insert) with metric fine pitch thread -- Product grades A and B 90.60 TC 2/SC 10
ISO 12126:1997
Prevailing torque type all-metal hexagon nuts with flange with metric fine pitch thread -- Product grades A and B 90.60 TC 2/SC 10
ISO 21670:2003
Hexagon weld nuts with flange 90.60 TC 2/SC 10

21.060.30 Washers, locking elements
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 887:2000
Plain washers for metric bolts, screws and nuts for general purposes -- General plan 90.93 TC 2/SC 10
ISO 887:2000/Cor 1:2006
60.60 TC 2/SC 10
ISO 4759-3:2000
Tolerances for fasteners -- Part 3: Plain washers for bolts, screws and nuts -- Product grades A and C 90.93 TC 2/SC 10
ISO 7089:2000
Plain washers -- Normal series -- Product grade A 90.93 TC 2/SC 10
ISO 7090:2000
Plain washers, chamfered -- Normal series -- Product grade A 90.93 TC 2/SC 10
ISO 7091:2000
Plain washers -- Normal series -- Product grade C 90.93 TC 2/SC 10
ISO 7092:2000
Plain washers -- Small series -- Product grade A 90.93 TC 2/SC 10
ISO 7093-1:2000
Plain washers -- Large series -- Part 1: Product grade A 90.93 TC 2/SC 10
ISO 7093-2:2000
Plain washers -- Large series -- Part 2: Product grade C 90.93 TC 2/SC 10
ISO 7094:2000
Plain washers -- Extra large series -- Product grade C 90.93 TC 2/SC 10
ISO 7094:2000/Cor 1:2000
60.60 TC 2/SC 10
ISO 8738:1986
Plain washers for clevis pins -- Product grade A 90.93 TC 2/SC 10
ISO 10644
Screw and washer assemblies made of steel with plain washers -- Washer hardness classes 200 HV and 300 HV 60.00 TC 2/SC 10
ISO 10644:1998
Screw and washer assemblies with plain washers -- Washer hardness classes 200 HV and 300 HV 90.92 TC 2/SC 10
ISO 10669:1999
Plain washers for tapping screw and washer assemblies -- Normal and large series -- Product grade A 90.20 TC 2/SC 10
ISO 10673
Plain washers for screw and washer assemblies -- Small, normal and large series -- Product grade A 60.00 TC 2/SC 10
ISO 10673:1998
Plain washers for screw and washer assemblies -- Small, normal and large series -- Product grade A 90.92 TC 2/SC 10

21.060.40 Rivets
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 1051:1999
Rivet shank diameters 90.20 TC 2/SC 10
ISO 14588:2000
Blind rivets -- Terminology and definitions 90.93 TC 2/SC 10
ISO 14589:2000
Blind rivets -- Mechanical testing 90.93 TC 2/SC 10
ISO 15973:2000
Closed end blind rivets with break pull mandrel and protruding head -- AlA/St 90.93 TC 2/SC 10
ISO 15974:2000
Closed end blind rivets with break pull mandrel and countersunk head -- AlA/St 90.93 TC 2/SC 10
ISO 15975:2002
Closed end blind rivets with break pull mandrel and protruding head -- AI/AIA 90.93 TC 2/SC 10
ISO 15976:2002
Closed end blind rivets with break pull mandrel and protruding head -- St/St 90.93 TC 2/SC 10
ISO 15977:2002
Open end blind rivets with break pull mandrel and protruding head -- AIA/St 90.93 TC 2/SC 10
ISO 15978:2002
Open end blind rivets with break pull mandrel and countersunk head -- AIA/St 90.93 TC 2/SC 10
ISO 15979:2002
Open end blind rivets with break pull mandrel and protruding head -- St/St 90.93 TC 2/SC 10
ISO 15980:2002
Open end blind rivets with break pull mandrel and countersunk head -- St/St 90.93 TC 2/SC 10
ISO 15981:2002
Open end blind rivets with break pull mandrel and protruding head -- AIA/AIA 90.93 TC 2/SC 10
ISO 15982:2002
Open end blind rivets with break pull mandrel and countersunk head -- AIA/AIA 90.93 TC 2/SC 10
ISO 15983:2002
Open end blind rivets with break pull mandrel and protruding head -- A2/A2 90.93 TC 2/SC 10
ISO 15984:2002
Open end blind rivets with break pull mandrel and countersunk head -- A2/A2 90.93 TC 2/SC 10
ISO 16582:2002
Open end blind rivets with break pull mandrel and protruding head -- Cu/St or Cu/Br or Cu/SSt 90.93 TC 2/SC 10
ISO 16583:2002
Open end blind rivets with break pull mandrel and countersunk head -- Cu/St or Cu/Br or Cu/SSt 90.93 TC 2/SC 10
ISO 16584:2002
Open end blind rivets with break pull mandrel and protruding head -- NiCu/St or NiCu/SSt 90.93 TC 2/SC 10
ISO 16585:2002
Closed end blind rivets with pull mandrel and protruding head -- A2/SSt 90.93 TC 2/SC 10

21.060.50 Pins, nails
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 1234:1997
Split pins 90.93 TC 2/SC 10
ISO 2338:1997
Parallel pins, of unhardened steel and austenitic stainless steel 90.93 TC 2/SC 10
ISO 2339:1986
Taper pins, unhardened 90.93 TC 2/SC 10
ISO 2340:1986
Clevis pins without head 90.93 TC 2/SC 10
ISO 2341:1986
Clevis pins with head 90.93 TC 2/SC 10
ISO 8733:1997
Parallel pins with internal thread, of unhardened steel and austenitic stainless steel 90.93 TC 2/SC 10
ISO 8734:1997
Parallel pins, of hardened steel and martensitic stainless steel (Dowel pins) 90.93 TC 2/SC 10
ISO 8735:1997
Parallel pins with internal thread, of hardened steel and martensitic stainless steel 90.93 TC 2/SC 10
ISO 8736:1986
Taper pins with internal thread, unhardened 90.93 TC 2/SC 10
ISO 8737:1986
Taper pins with external thread, unhardened 90.93 TC 2/SC 10
ISO 8739:1997
Grooved pins -- Full-length parallel grooved, with pilot 90.93 TC 2/SC 10
ISO 8740:1997
Grooved pins -- Full-length parallel grooved, with chamfer 90.93 TC 2/SC 10
ISO 8741:1997
Grooved pins -- Half-length reverse-taper grooved 90.93 TC 2/SC 10
ISO 8742:1997
Grooved pins -- One-third-length centre grooved 90.93 TC 2/SC 10
ISO 8743:1997
Grooved pins -- Half-length centre grooved 90.93 TC 2/SC 10
ISO 8744:1997
Grooved pins -- Full-length taper grooved 90.93 TC 2/SC 10
ISO 8745:1997
Grooved pins -- Half-length taper grooved 90.93 TC 2/SC 10
ISO 8746:1997
Grooved pins with round head 90.93 TC 2/SC 10
ISO 8747:1997
Grooved pins with countersunk head 90.93 TC 2/SC 10
ISO 8748:2007
Spring-type straight pins -- Coiled, heavy duty 60.60 TC 2/SC 10
ISO 8749:1986
Pins and grooved pins -- Shear test 90.93 TC 2/SC 10
ISO 8750:2007
Spring-type straight pins -- Coiled, standard duty 60.60 TC 2/SC 10
ISO 8751:2007
Spring-type straight pins -- Coiled, light duty 60.60 TC 2/SC 10
ISO 8752
Spring-type straight pins -- Slotted, heavy duty 60.00 TC 2/SC 10
ISO 8752:1997
Spring-type straight pins -- Slotted, heavy duty 90.92 TC 2/SC 10
ISO 13337:1997
Spring-type straight pins -- Slotted, light duty 90.92 TC 2/SC 10
ISO 13337
Spring-type straight pins -- Slotted, light duty 60.00 TC 2/SC 10

? 2009 ISO
Privacy Policy
Name and logo
Sitemap
Contact ISO
Guided tour of ISO-Online
Print
Increase text size
Decrease text size
News feeds


21.060.60 Rings, bushes, sleeves, collars
21.060.70 Clamps and staples
21.060.99 Other fasteners

21.100 Bearings
ICS Field
21.100.01 Bearings in general
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 21107:2004
Rolling bearings and spherical plain bearings -- Search structure for electronic media -- Characteristics and performance criteria identified by attribute vocabulary 90.93 TC 4

21.100.10 Plain bearings
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 2795:1991
Plain bearings -- Sintered bushes -- Dimensions and tolerances 90.93 TC 123/SC 3
ISO 3547-1:2006
Plain bearings -- Wrapped bushes -- Part 1: Dimensions 60.60 TC 123/SC 3
ISO 3547-2:2006
Plain bearings -- Wrapped bushes -- Part 2: Test data for outside and inside diameters 60.60 TC 123/SC 3
ISO 3547-3:2006
Plain bearings -- Wrapped bushes -- Part 3: Lubrication holes, grooves and indentations 60.60 TC 123/SC 3
ISO 3547-4:2006
Plain bearings -- Wrapped bushes -- Part 4: Materials 60.60 TC 123/SC 3
ISO 3547-5:2007
Plain bearings -- Wrapped bushes -- Part 5: Checking the outside diameter 60.60 TC 123/SC 5
ISO 3547-6:2007
Plain bearings -- Wrapped bushes -- Part 6: Checking the inside diameter 60.60 TC 123/SC 5
ISO 3547-7:2007
Plain bearings -- Wrapped bushes -- Part 7: Measurement of wall thickness of thin-walled bushes 60.60 TC 123/SC 5
ISO 3548:1999
Plain bearings -- Thin-walled half bearings with or without flange -- Tolerances, design features and methods of test 90.20 TC 123/SC 3
ISO/PRF 3548-2
Plain bearings -- Thin-walled half bearings with or without flange -- Part 2: Measurement of wall thickness and flange thickness 50.00 TC 123/SC 5
ISO/FDIS 4378-1
Plain bearings -- Terms, definitions, classification and symbols -- Part 1: Design, bearing materials and their properties 50.20 TC 123/SC 6
ISO 4378-1:1997
Plain bearings -- Terms, definitions and classification -- Part 1: Design, bearing materials and their properties 90.92 TC 123/SC 6
ISO 4378-2:1983
Plain bearings -- Terms, definitions and classification -- Part 2: Friction and wear 90.92 TC 123/SC 6
ISO/FDIS 4378-2
Plain bearings -- Terms, definitions, classification and symbols -- Part 2: Friction and wear 50.20 TC 123/SC 6
ISO/FDIS 4378-3
Plain bearings -- Terms, definitions, classification and symbols -- Part 3: Lubrication 50.20 TC 123/SC 6
ISO 4378-3:1983
Plain bearings -- Terms, definitions and classification -- Part 3: Lubrication 90.92 TC 123/SC 6
ISO/FDIS 4378-4
Plain bearings -- Terms, definitions, classification and symbols -- Part 4: Basic symbols 50.20 TC 123/SC 6
ISO 4378-4:1997
Plain bearings -- Terms, definitions and classification -- Part 4: Calculation parameters and their symbol 90.92 TC 123/SC 6
ISO/FDIS 4378-5
Plain bearings -- Terms, definitions, classification and symbols -- Part 5: Application of symbols 50.20 TC 123/SC 6
ISO 4379:1993
Plain bearings -- Copper alloy bushes 90.93 TC 123/SC 3
ISO 4381:2000
Plain bearings -- Lead and tin casting alloys for multilayer plain bearings 90.92 TC 123/SC 2
ISO 4382-1:1991
Plain bearings -- Copper alloys -- Part 1: Cast copper alloys for solid and multilayer thick-walled plain bearings 90.93 TC 123/SC 2
ISO 4382-2:1991
Plain bearings -- Copper alloys -- Part 2: Wrought copper alloys for solid plain bearings 90.93 TC 123/SC 2
ISO 4383:2000
Plain bearings -- Multilayer materials for thin-walled plain bearings 90.92 TC 123/SC 2
ISO 4384-1:2000
Plain bearings -- Hardness testing of bearing metals -- Part 1: Compound materials 90.92 TC 123/SC 2
ISO 4384-2:1982
Plain bearings -- Hardness testing of bearing metals -- Part 2: Solid materials 90.60 TC 123/SC 2
ISO 4385:1981
Plain bearings -- Compression testing of metallic bearing materials 90.60 TC 123/SC 2
ISO 4386-1:1992
Plain bearings -- Metallic multilayer plain bearings -- Part 1: Non-destructive ultrasonic testing of bond 90.92 TC 123/SC 2
ISO 4386-2:1982
Plain bearings -- Metallic multilayer plain bearings -- Part 2: Destructive testing of bond for bearing metal layer thicknesses greater than or equal to 2 mm 90.92 TC 123/SC 2
ISO 4386-3:1992
Plain bearings -- Metallic multilayer plain bearings -- Part 3: Non-destructive penetrant testing 90.60 TC 123/SC 2
ISO 6279:2006
Plain bearings -- Aluminium alloys for solid bearings 90.20 TC 123/SC 2
ISO 6280:1981
Plain bearings -- Requirements on backings for thick-walled multilayer bearings 90.60 TC 123
ISO 6281:2007
Plain bearings -- Testing under conditions of hydrodynamic and mixed lubrication in test rigs 60.60 TC 123/SC 2
ISO 6282:1983
Plain bearings -- Metallic thin-walled half bearings -- Determination of the sigma 0,01*-limit 90.60 TC 123/SC 2
ISO 6524:1992
Plain bearings -- Thin-walled half-bearings -- Checking of peripheral length 90.60 TC 123/SC 3
ISO 6525:1983
Plain bearings -- Ring type thrust washers made from strip -- Dimensions and tolerances 90.60 TC 123/SC 3
ISO 6526:1983
Plain bearings -- Pressed bimetallic half thrust washers -- Features and tolerances 90.60 TC 123/SC 3
ISO 6691:2000
Thermoplastic polymers for plain bearings -- Classification and designation 90.93 TC 123/SC 2
ISO 6811:1998
Spherical plain bearings -- Vocabulary 90.60 TC 4/SC 7
ISO 6811:1998/Cor 1:1999
60.60 TC 4/SC 7
ISO 7146-1:2008
Plain bearings -- Appearance and characterization of damage to metallic hydrodynamic bearings -- Part 1: General 60.60 TC 123/SC 2
ISO 7146-2:2008
Plain bearings -- Appearance and characterization of damage to metallic hydrodynamic bearings -- Part 2: Cavitation erosion and its countermeasures 60.60 TC 123/SC 2
ISO 7148-1:1999
Plain bearings -- Testing of the tribological behaviour of bearing materials -- Part 1: Testing of bearing metals 90.92 TC 123/SC 2
ISO 7148-2:1999
Plain bearings -- Testing of the tribological behaviour of bearing materials -- Part 2: Testing of polymer-based bearing materials 90.92 TC 123/SC 2
ISO 7902-1:1998
Hydrodynamic plain journal bearings under steady-state conditions -- Circular cylindrical bearings -- Part 1: Calculation procedure 90.60 TC 123/SC 4
ISO 7902-2:1998
Hydrodynamic plain journal bearings under steady-state conditions -- Circular cylindrical bearings -- Part 2: Functions used in the calculation procedure 90.60 TC 123/SC 4
ISO 7902-3:1998
Hydrodynamic plain journal bearings under steady-state conditions -- Circular cylindrical bearings -- Part 3: Permissible operational parameters 90.60 TC 123/SC 4
ISO 7904-1:1995
Plain bearings -- Symbols -- Part 1: Basic symbols 90.92 TC 123/SC 6
ISO 7904-2:1995
Plain bearings -- Symbols -- Part 2: Applications 90.92 TC 123/SC 6
ISO 7905-1:1995
Plain bearings -- Bearing fatigue -- Part 1: Plain bearings in test rigs and in applications under conditions of hydrodynamic lubrication 90.93 TC 123/SC 2
ISO 7905-2:1995
Plain bearings -- Bearing fatigue -- Part 2: Test with a cylindrical specimen of a metallic bearing material 90.93 TC 123/SC 2
ISO 7905-3:1995
Plain bearings -- Bearing fatigue -- Part 3: Test on plain strips of a metallic multilayer bearing material 90.93 TC 123/SC 2
ISO 7905-4:1995
Plain bearings -- Bearing fatigue -- Part 4: Tests on half-bearings of a metallic multilayer bearing material 90.93 TC 123/SC 2
ISO 10129:2006
Plain bearings -- Testing of bearing metals -- Resistance to corrosion by lubricants under static conditions 90.20 TC 123/SC 2
ISO 11687-1:1995
Plain bearings -- Pedestal plain bearings -- Part 1: Pillow blocks 90.93 TC 123/SC 3
ISO 11687-2:1995
Plain bearings -- Pedestal plain bearings -- Part 2: Side flange bearings 90.93 TC 123/SC 3
ISO 11687-3:1995
Plain bearings -- Pedestal plain bearings -- Part 3: Centre flange bearings 90.93 TC 123/SC 3
ISO 12128:2001
Plain bearings -- Lubrication holes, grooves and pockets -- Dimensions, types, designation and their application to bearing bushes 90.93 TC 123/SC 3
ISO 12129-1:1995
Plain bearings -- Part 1: Fits 90.93 TC 123/SC 3
ISO 12129-2:1995
Plain bearings -- Part 2: Tolerances on form and position and surface roughness for shafts, flanges and thrust collars 90.93 TC 123/SC 3
ISO 12130-1:2001
Plain bearings -- Hydrodynamic plain tilting pad thrust bearings under steady-state conditions -- Part 1: Calculation of tilting pad thrust bearings 90.60 TC 123/SC 4
ISO 12130-2:2001
Plain bearings -- Hydrodynamic plain tilting pad thrust bearings under steady-state conditions -- Part 2: Functions for calculation of tilting pad thrust bearings 90.60 TC 123/SC 4
ISO 12130-3:2001
Plain bearings -- Hydrodynamic plain tilting pad thrust bearings under steady-state conditions -- Part 3: Guide values for the calculation of tilting pad thrust bearings 90.60 TC 123/SC 4
ISO 12131-1:2001
Plain bearings -- Hydrodynamic plain thrust pad bearings under steady-state conditions -- Part 1: Calculation of thrust pad bearings 90.60 TC 123/SC 4
ISO 12131-2:2001
Plain bearings -- Hydrodynamic plain thrust pad bearings under steady-state conditions -- Part 2: Functions for the calculation of thrust pad bearings 90.60 TC 123/SC 4
ISO 12131-3:2001
Plain bearings -- Hydrodynamic plain thrust pad bearings under steady-state conditions -- Part 3: Guide values for the calculation of thrust pad bearings 90.60 TC 123/SC 4
ISO 12132:1999
Plain bearings -- Quality assurance of thin- walled half bearings -- Design FMEA 90.20 TC 123/SC 5
ISO 12167-1:2001
Plain bearings -- Hydrostatic plain journal bearings with drainage grooves under steady-state conditions -- Part 1: Calculation of oil-lubricated plain journal bearings with drainage grooves 90.60 TC 123/SC 4
ISO 12167-2:2001
Plain bearings -- Hydrostatic plain journal bearings with drainage grooves under steady-state conditions -- Part 2: Characteristic values for the calculation of oil-lubricated plain journal bearings with drainage grooves 90.60 TC 123/SC 4
ISO 12168-1:2001
Plain bearings -- Hydrostatic plain journal bearings without drainage grooves under steady-state conditions -- Part 1: Calculation of oil-lubricated plain journal bearings without drainage grooves 90.60 TC 123/SC 4
ISO 12168-2:2001
Plain bearings -- Hydrostatic plain journal bearings without drainage grooves under steady-state conditions -- Part 2: Characteristic values for the calculation of oil-lubricated plain journal bearings without drainage grooves 90.60 TC 123/SC 4
ISO 12240-1:1998
Spherical plain bearings -- Part 1: Radial spherical plain bearings 90.60 TC 4/SC 7
ISO 12240-2:1998
Spherical plain bearings -- Part 2: Angular contact radial spherical plain bearings 90.60 TC 4/SC 7
ISO 12240-3:1998
Spherical plain bearings -- Part 3: Thrust spherical plain bearings 90.60 TC 4/SC 7
ISO 12240-4:1998
Spherical plain bearings -- Part 4: Spherical plain bearing rod ends 90.60 TC 4/SC 7
ISO 12240-4:1998/Cor 1:1999
60.60 TC 4/SC 7
ISO 12301:2007
Plain bearings -- Quality control techniques and inspection of geometrical and material quality characteristics 60.60 TC 123/SC 5
ISO 12302:1993
Plain bearings -- Quality characteristics -- Statistical process control (SPC) 90.60 TC 123/SC 5
ISO 12303:1995
Plain bearings -- Quality characteristics -- Calculation of machine and process capabilities 90.93 TC 123/SC 5
ISO 12308:1994
Plain bearings -- Quality assurance -- Sample types -- Definitions, applications and testing 90.20 TC 123/SC 5
ISO 13778:1999
Plain bearings -- Quality assurance of thin-walled half bearings -- Selective assembly of bearings to achieve a narrow clearance range 90.20 TC 123/SC 5
ISO 16287:2005
Plain bearings -- Thermoplastic bushes -- Dimensions and tolerances 90.93 TC 123/SC 3
ISO/CD TR 27507
Plain bearings -- Recommendations for automotive crankshaft bearing environments 30.99 TC 123/SC 3

21.100.20 Rolling bearings
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 15:1998
Rolling bearings -- Radial bearings -- Boundary dimensions, general plan 90.60 TC 4
ISO 76:2006
Rolling bearings -- Static load ratings 90.60 TC 4/SC 8
ISO 104:2002
Rolling bearings -- Thrust bearings -- Boundary dimensions, general plan 90.93 TC 4
ISO 113:1999
Rolling bearings -- Plummer block housings -- Boundary dimensions 90.60 TC 4
ISO 199:2005
Rolling bearings -- Thrust bearings -- Tolerances 90.60 TC 4/SC 4
ISO 246:2007
Rolling bearings -- Cylindrical roller bearings, separate thrust collars -- Boundary dimensions 60.60 TC 4
ISO 281:2007
Rolling bearings -- Dynamic load ratings and rating life 60.60 TC 4/SC 8
ISO 355:2007
Rolling bearings -- Tapered roller bearings -- Boundary dimensions and series designations 60.60 TC 4/SC 9
ISO 464:1995
Rolling bearings -- Radial bearings with locating snap ring -- Dimensions and tolerances 90.93 TC 4
ISO 492:2002
Rolling bearings -- Radial bearings -- Tolerances 90.93 TC 4/SC 4
ISO 582:1995
Rolling bearings -- Chamfer dimensions -- Maximum values 90.93 TC 4
ISO 1132-1:2000
Rolling bearings -- Tolerances -- Part 1: Terms and definitions 90.93 TC 4
ISO 1132-2:2001
Rolling bearings -- Tolerances -- Part 2: Measuring and gauging principles and methods 90.93 TC 4
ISO 1206:2001
Rolling bearings -- Needle roller bearings, dimension series 48, 49 and 69 -- Boundary dimensions and tolerances 90.93 TC 4/SC 5
ISO 1224-1:2007
Rolling bearings -- Instrument precision bearings -- Part 1: Boundary dimensions, tolerances and characteristics of metric series bearings 60.60 TC 4
ISO 1224-2:2007
Rolling bearings -- Instrument precision bearings -- Part 2: Boundary dimensions, tolerances and characteristics of inch series bearings 60.60 TC 4
ISO/TR 1281-1:2008
Rolling bearings -- Explanatory notes on ISO 281 -- Part 1: Basic dynamic load rating and basic rating life 60.60 TC 4/SC 8
ISO/TR 1281-2:2008
Rolling bearings -- Explanatory notes on ISO 281 -- Part 2: Modified rating life calculation, based on a systems approach to fatigue stresses 60.60 TC 4/SC 8
ISO 2982-1:1995
Rolling bearings -- Accessories -- Part 1: Tapered sleeves -- Dimensions 90.93 TC 4
ISO 2982-2:2001
Rolling bearings -- Accessories -- Part 2: Locknuts and locking devices -- Dimensions 90.93 TC 4
ISO/CD 3030
Rolling bearings -- Radial needle roller and cage assemblies -- Dimensions and tolerances 30.60 TC 4/SC 5
ISO 3030:1996
Rolling bearings -- Radial needle roller and cage assemblies -- Dimensions and tolerances 90.92 TC 4/SC 5
ISO 3031:2000
Rolling bearings -- Thrust needle roller and cage assemblies, thrust washers -- Boundary dimensions and tolerances 90.93 TC 4/SC 5
ISO 3096:1996
Rolling bearings -- Needle rollers -- Dimensions and tolerances 90.92 TC 4/SC 5
ISO/NP 3096
Rolling bearings -- Needle rollers -- Dimensions and tolerances 10.99 TC 4/SC 5
ISO 3096:1996/Cor 1:1999
60.60 TC 4/SC 5
ISO 3228:1993
Rolling bearings -- Cast and pressed housings for insert bearings 90.92 TC 4/SC 6
ISO/CD 3228
Rolling bearings -- Cast and pressed housings for insert bearings 30.60 TC 4/SC 6
ISO 3245:2007
Rolling bearings -- Needle roller bearings, drawn cup without inner ring -- Boundary dimensions and tolerances 60.60 TC 4/SC 5
ISO 3290-1:2008
Rolling bearings -- Balls -- Part 1: Steel balls 60.60 TC 4
ISO 3290-1:2008/Cor 1:2009
60.60 TC 4
ISO 3290-2:2008
Rolling bearings -- Balls -- Part 2: Ceramic balls 60.60 TC 4
ISO 5593:1997
Rolling bearings -- Vocabulary 90.92 TC 4
ISO 5593:1997/Amd 1:2007
60.60 TC 4
ISO 5753:1991
Rolling bearings -- Radial internal clearance 90.92 TC 4/SC 4
ISO/FDIS 5753-1
Rolling bearings -- Internal clearance -- Part 1: Radial internal clearance for radial bearings 50.00 TC 4/SC 4
ISO/CD 5753-2
Rolling bearings -- Internal clearance -- Part 2: Axial 30.20 TC 4/SC 4
ISO 7063:2003
Rolling bearings -- Needle roller bearing track rollers -- Boundary dimensions and tolerances 90.60 TC 4/SC 5
ISO 8443:1999
Rolling bearings -- Radial ball bearings with flanged outer ring -- Flange dimensions 90.60 TC 4
ISO 8826-1:1989
Technical drawings -- Rolling bearings -- Part 1: General simplified representation 90.93 TC 10/SC 6
ISO 8826-2:1994
Technical drawings -- Rolling bearings -- Part 2: Detailed simplified representation 90.93 TC 10/SC 6
ISO 9628:2006
Rolling bearings -- Insert bearings and eccentric locking collars -- Boundary dimensions and tolerances 90.20 TC 4/SC 6
ISO 9628:2006/CD Amd 1
30.60 TC 4/SC 6
ISO 10285:2007
Rolling bearings -- Sleeve type linear ball bearings -- Boundary dimensions and tolerances 60.60 TC 4/SC 11
ISO 10317:2008
Rolling bearings -- Tapered roller bearings -- Designation system 60.60 TC 4/SC 9
ISO/TR 10657:1991
Explanatory notes on ISO 76 90.93 TC 4/SC 8
ISO 12043:2007
Rolling bearings -- Single-row cylindrical roller bearings -- Chamfer dimensions for loose rib and non-rib sides 60.60 TC 4
ISO 12044:1995
Rolling bearings -- Single-row angular contact ball bearings -- Chamfer dimensions for outer ring non-thrust side 90.93 TC 4
ISO/FDIS 12090-1
Rolling bearings -- Linear motion, recirculating ball and roller profiled rail guides -- Part 1: Boundary dimensions and tolerances for series 1, 2 and 3 50.00 TC 4/SC 11
ISO/FDIS 12090-2
Rolling bearings -- Linear motion, recirculating ball and roller profiled rail guides -- Part 2: Boundary dimensions and tolerances for series 4 and 5 50.00 TC 4/SC 11
ISO/CD 12225
Rolling bearings -- Insert bearing units -- Boundary dimensions 30.60 TC 4/SC 6
ISO/NP 12297-1
Rolling bearings -- Cylindrical rollers -- Part 1: Steel rollers 10.99 TC 4
ISO/NP 12297-2
Rolling bearings -- Cylindrical rollers -- Part 2: Ceramic rollers 10.99 TC 4
ISO 13012-1:2009
Rolling bearings -- Accessories for sleeve type linear ball bearings -- Part 1: Boundary dimensions and tolerances for series 1 and 3 60.60 TC 4/SC 11
ISO 13012-2:2009
Rolling bearings -- Accessories for sleeve type linear ball bearings -- Part 2: Boundary dimensions and tolerances for series 5 60.60 TC 4/SC 11
ISO 14728-1:2004
Rolling bearings -- Linear motion rolling bearings -- Part 1: Dynamic load ratings and rating life 90.93 TC 4/SC 8
ISO 14728-2:2004
Rolling bearings -- Linear motion rolling bearings -- Part 2: Static load ratings 90.93 TC 4/SC 8
ISO 15241:2001
Rolling bearings -- Symbols for quantities 90.93 TC 4
ISO 15242-1:2004
Rolling bearings -- Measuring methods for vibration -- Part 1: Fundamentals 90.93 TC 4
ISO 15242-2:2004
Rolling bearings -- Measuring methods for vibration -- Part 2: Radial ball bearings with cylindrical bore and outside surface 90.93 TC 4
ISO 15242-3:2006
Rolling bearings -- Measuring methods for vibration -- Part 3: Radial spherical and tapered roller bearings with cylindrical bore and outside surface 90.20 TC 4
ISO 15242-4:2007
Rolling bearings -- Measuring methods for vibration -- Part 4: Radial cylindrical roller bearings with cylindrical bore and outside surface 60.60 TC 4
ISO 15243:2004
Rolling bearings -- Damage and failures -- Terms, characteristics and causes 90.93 TC 4
ISO 15312:2003
Rolling bearings -- Thermal speed rating -- Calculation and coefficients 90.60 TC 4/SC 8
ISO/TS 16281:2008
Rolling bearings -- Methods for calculating the modified reference rating life for universally loaded bearings 60.60 TC 4/SC 8
ISO/TS 16281:2008/Cor 1:2009
60.60 TC 4/SC 8
ISO 20515:2007
Rolling bearings -- Radial bearings, retaining slots -- Dimensions and tolerances 60.60 TC 4
ISO 20516:2007
Rolling bearings -- Aligning thrust ball bearings and aligning seat washers -- Boundary dimensions 60.60 TC 4
ISO/CD TS 23768
Rolling bearings -- Parts library -- Reference dictionary 30.60 TC 4
ISO 24393:2008
Rolling bearings -- Linear motion rolling bearings -- Vocabulary 60.60 TC 4


21.120 Shafts and couplings
ICS Field
21.120.01 Shafts and couplings in general
21.120.10 Shafts
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 496:1973
Driving and driven machines -- Shaft heights 90.60 TC 14

21.120.20 Couplings
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 4863:1984
Resilient shaft couplings -- Information to be supplied by users and manufacturers 90.93 TC 108
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 14:1982
Straight-sided splines for cylindrical shafts with internal centering -- Dimensions, tolerances and verification 90.60 TC 14
ISO 3117:1977
Tangential keys and keyways 90.60 TC 14
ISO 3912:1977
Woodruff keys and keyways 90.60 TC 14
ISO 4156-1:2005
Straight cylindrical involute splines -- Metric module, side fit -- Part 1: Generalities 90.60 TC 14
ISO 4156-2:2005
Straight cylindrical involute splines -- Metric module, side fit -- Part 2: Dimensions 90.60 TC 14
ISO 4156-3:2005
Straight cylindrical involute splines -- Metric module, side fit -- Part 3: Inspection 90.60 TC 14
ISO 6413:1988
Technical drawings -- Representation of splines and serrations 90.93 TC 10/SC 6


21.120.30 Keys and keyways, splines
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 14:1982
Straight-sided splines for cylindrical shafts with internal centering -- Dimensions, tolerances and verification 90.60 TC 14
ISO 3117:1977
Tangential keys and keyways 90.60 TC 14
ISO 3912:1977
Woodruff keys and keyways 90.60 TC 14
ISO 4156-1:2005
Straight cylindrical involute splines -- Metric module, side fit -- Part 1: Generalities 90.60 TC 14
ISO 4156-2:2005
Straight cylindrical involute splines -- Metric module, side fit -- Part 2: Dimensions 90.60 TC 14
ISO 4156-3:2005
Straight cylindrical involute splines -- Metric module, side fit -- Part 3: Inspection 90.60 TC 14
ISO 6413:1988
Technical drawings -- Representation of splines and serrations 90.93 TC 10/SC 6

21.120.40 Balancing and balancing machines
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 1925:2001
Mechanical vibration -- Balancing -- Vocabulary 90.93 TC 108
ISO 1940-1:2003
Mechanical vibration -- Balance quality requirements for rotors in a constant (rigid) state -- Part 1: Specification and verification of balance tolerances 90.92 TC 108
ISO 1940-1:2003/Cor 1:2005
60.60 TC 108
ISO 1940-2:1997
Mechanical vibration -- Balance quality requirements of rigid rotors -- Part 2: Balance errors 90.92 TC 108
ISO 2953:1999
Mechanical vibration -- Balancing machines -- Description and evaluation 90.93 TC 108
ISO 3719:1994
Mechanical vibration -- Symbols for balancing machines and associated instrumentation 90.93 TC 108
ISO 7475:2002
Mechanical vibration -- Balancing machines -- Enclosures and other protective measures for the measuring station 90.92 TC 108
ISO 8821:1989
Mechanical vibration -- Balancing -- Shaft and fitment key convention 90.93 TC 108
ISO 10814:1996
Mechanical vibration -- Susceptibility and sensitivity of machines to unbalance 90.92 TC 108
ISO 11342:1998
Mechanical vibration -- Methods and criteria for the mechanical balancing of flexible rotors 90.92 TC 108
ISO 11342:1998/Cor 1:2000
60.60 TC 108
ISO 14694:2003
Industrial fans -- Specifications for balance quality and vibration levels 90.93 TC 117
ISO 19499:2007
Mechanical vibration -- Balancing -- Guidance on the use and application of balancing standards 60.60 TC 108
ISO/FDIS 20806
Mechanical vibration -- Criteria and safeguards for the in-situ balancing of medium and large rotors 50.20 TC 108
ISO 20806:2004
Mechanical vibration -- Criteria and safeguards for the in-situ balancing of medium and large rotors 90.92 TC 108

21.120.99 Other standards related to shafts and couplings

21.140 Seals, glands
Seals for pipe and hose assemblies, see 23.040.80
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 4708:2000
Composition cork -- Gasket material -- Test methods 90.93 TC 87
ISO 4709:2000
Composition cork -- Gasket material -- Classification system, requirements, sampling, packaging and marking 90.93 TC 87
ISO 9222-1:1989
Technical drawings -- Seals for dynamic application -- Part 1: General simplified representation 90.93 TC 10/SC 6
ISO 9222-2:1989
Technical drawings -- Seals for dynamic application -- Part 2: Detailed simplified representation 90.93 TC 10/SC 6

21.160 Springs
Steels for springs, see 77.140.25
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 2162-1:1993
Technical product documentation -- Springs -- Part 1: Simplified representation 90.93 TC 10/SC 6
ISO 2162-2:1993
Technical product documentation -- Springs -- Part 2: Presentation of data for cylindrical helical compression springs 90.93 TC 227
ISO 2162-3:1993
Technical product documentation -- Springs -- Part 3: Vocabulary 90.92 TC 227
ISO/CD 11891
Hot formed helical compression springs -- Technical specifications 30.20 TC 227
ISO/PRF 26909
Springs -- Vocabulary 50.20 TC 227
ISO 26910-1
Springs -- Shot peening -- Part 1: General procedures 60.00 TC 227

21.180 Housings, enclosures, other machine parts
21.200 Gears
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 53:1998
Cylindrical gears for general and heavy engineering -- Standard basic rack tooth profile 90.93 TC 60
ISO 54:1996
Cylindrical gears for general engineering and for heavy engineering -- Modules 90.93 TC 60
ISO 677:1976
Straight bevel gears for general engineering and heavy engineering -- Basic rack 90.20 TC 60
ISO 678:1976
Straight bevel gears for general engineering and heavy engineering -- Modules and diametral pitches 90.93 TC 60
ISO 701:1998
International gear notation -- Symbols for geometrical data 90.93 TC 60/SC 1
ISO 1122-1:1998
Vocabulary of gear terms -- Part 1: Definitions related to geometry 90.93 TC 60/SC 1
ISO 1122-1:1998/Cor 1:1999
60.60 TC 60/SC 1
ISO 1122-1:1998/Cor 2
60.00 TC 60/SC 1
ISO 1122-2:1999
Vocabulary of gear terms -- Part 2: Definitions related to worm gear geometry 90.93 TC 60/SC 1
ISO/NP 1328-1
Cylindrical gears -- ISO system of accuracy -- Part 1: Definitions and allowable values of deviations relevant to corresponding flanks of gear teeth 10.99 TC 60
ISO 1328-1:1995
Cylindrical gears -- ISO system of accuracy -- Part 1: Definitions and allowable values of deviations relevant to corresponding flanks of gear teeth 90.92 TC 60
ISO 1328-2:1997
Cylindrical gears -- ISO system of accuracy -- Part 2: Definitions and allowable values of deviations relevant to radial composite deviations and runout information 90.93 TC 60
ISO 1340:1976
Cylindrical gears -- Information to be given to the manufacturer by the purchaser in order to obtain the gear required 90.20 TC 60
ISO 1341:1976
Straight bevel gears -- Information to be given to the manufacturer by the purchaser in order to obtain the gear required 90.20 TC 60
ISO 2203:1973
Technical drawings -- Conventional representation of gears 90.93 TC 10/SC 6
ISO 2490:2007
Solid (monobloc) gear hobs with tenon drive or axial keyway, 0,5 to 40 module -- Nominal dimensions 60.60 TC 60/SC 1
ISO 4468:2009
Gear hobs -- Accuracy requirements 60.60 TC 60/SC 1
ISO 6336-1:2006
Calculation of load capacity of spur and helical gears -- Part 1: Basic principles, introduction and general influence factors 60.60 TC 60/SC 2
ISO 6336-1:2006/Cor 1:2008
60.60 TC 60/SC 2
ISO 6336-2:2006
Calculation of load capacity of spur and helical gears -- Part 2: Calculation of surface durability (pitting) 60.60 TC 60/SC 2
ISO 6336-2:2006/Cor 1:2008
60.60 TC 60/SC 2
ISO 6336-3:2006
Calculation of load capacity of spur and helical gears -- Part 3: Calculation of tooth bending strength 60.60 TC 60/SC 2
ISO 6336-3:2006/Cor 1:2008
60.60 TC 60/SC 2
ISO 6336-5:2003
Calculation of load capacity of spur and helical gears -- Part 5: Strength and quality of materials 90.60 TC 60/SC 2
ISO 6336-6:2006
Calculation of load capacity of spur and helical gears -- Part 6: Calculation of service life under variable load 60.60 TC 60/SC 2
ISO 6336-6:2006/Cor 1:2007
60.60 TC 60/SC 2
ISO/NP 6336-7
Calculation of load capacity of spur and helical gears -- Part 7: Calculation of micro-pitting 10.99 TC 60/SC 2
ISO 8579-1:2002
Acceptance code for gear units -- Part 1: Test code for airborne sound 90.93 TC 60
ISO 8579-2:1993
Acceptance code for gears -- Part 2: Determination of mechanical vibrations of gear units during acceptance testing 90.20 TC 60
ISO 9083:2001
Calculation of load capacity of spur and helical gears -- Application to marine gears 90.93 TC 60/SC 2
ISO 9085:2002
Calculation of load capacity of spur and helical gears -- Application for industrial gears 90.60 TC 60/SC 2
ISO/TR 10064-1:1992
Code of inspection practice -- Part 1: Inspection of corresponding flanks of gear teeth 90.93 TC 60
ISO/TR 10064-1:1992/Cor 1:2006
60.60 TC 60
ISO/TR 10064-2:1996
Code of inspection practice -- Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash 90.93 TC 60
ISO/TR 10064-2:1996/Cor 1:2001
60.60 TC 60
ISO/TR 10064-2:1996/Cor 2:2006
60.60 TC 60
ISO/TR 10064-3:1996
Code of inspection practice -- Part 3: Recommendations relative to gear blanks, shaft centre distance and parallelism of axes 90.93 TC 60
ISO/TR 10064-3:1996/Cor 1:2006
60.60 TC 60
ISO/TR 10064-4:1998
Code of inspection practice -- Part 4: Recommendations relative to surface texture and tooth contact pattern checking 90.93 TC 60
ISO/TR 10064-4:1998/Cor 1:2006
60.60 TC 60
ISO/TR 10064-5:2005
Code of inspection practice -- Part 5: Recommendations relative to evaluation of gear measuring instruments 60.60 TC 60
ISO/TR 10064-5:2005/Cor 1:2006
60.60 TC 60
ISO/TR 10064-6:2009
Code of inspection practice -- Part 6: Bevel gear measurement methods 60.60 TC 60
ISO/NP 10300-1
Calculation of load capacity of bevel gears -- Part 1: Introduction and general influence factors 10.99 TC 60/SC 2
ISO 10300-1:2001
Calculation of load capacity of bevel gears -- Part 1: Introduction and general influence factors 90.92 TC 60/SC 2
ISO 10300-2:2001
Calculation of load capacity of bevel gears -- Part 2: Calculation of surface durability (pitting) 90.92 TC 60/SC 2
ISO/NP 10300-2
Calculation of load capacity of bevel gears -- Part 2: Calculation of surface durability (pitting) 10.99 TC 60/SC 2
ISO 10300-3:2001
Calculation of load capacity of bevel gears -- Part 3: Calculation of tooth root strength 90.92 TC 60/SC 2
ISO/NP 10300-3
Calculation of load capacity of bevel gears -- Part 3: Calculation of tooth root strength 10.99 TC 60/SC 2
ISO 10825:1995
Gears -- Wear and damage to gear teeth -- Terminology 90.93 TC 60/SC 1
ISO/TR 10828:1997
Worm gears -- Geometry of worm profiles 90.93 TC 60/SC 1
ISO/TR 10828:1997/Cor 1:1998
60.60 TC 60/SC 1
ISO/TR 13593:1999
Enclosed gear drives for industrial applications 90.93 TC 60
ISO/TR 13593:1999/Cor 1:2005
60.60 TC 60
ISO 13691:2001
Petroleum and natural gas industries -- High-speed special-purpose gear units 90.93 TC 60/SC 2
ISO/TR 13989-1:2000
Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears -- Part 1: Flash temperature method 90.93 TC 60/SC 2
ISO/TR 13989-2:2000
Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears -- Part 2: Integral temperature method 90.93 TC 60/SC 2
ISO 14104:1995
Gears -- Surface temper etch inspection after grinding 90.93 TC 60/SC 2
ISO/TR 14179-1:2001
Gears -- Thermal capacity -- Part 1: Rating gear drives with thermal equilibrium at 95 °C sump temperature 90.93 TC 60/SC 2
ISO/TR 14179-2:2001
Gears -- Thermal capacity -- Part 2: Thermal load-carrying capacity 90.93 TC 60/SC 2
ISO/CD TR 14521
Gear -- Calculation of load capacity of wormgears 30.60 TC 60/SC 1
ISO 14635-1:2000
Gears -- FZG test procedures -- Part 1: FZG test method A/8,3/90 for relative scuffing load-carrying capacity of oils 90.93 TC 60/SC 2
ISO 14635-2:2004
Gears -- FZG test procedures -- Part 2: FZG step load test A10/16, 6R/120 for relative scuffing load-carrying capacity of high EP oils 90.60 TC 60/SC 2
ISO 14635-3:2005
Gears -- FZG test procedures -- Part 3: FZG test method A/2, 8/50 for relative scuffing load-carrying capacity and wear characteristics of semifluid gear greases 90.60 TC 60/SC 2
ISO 17485:2006
Bevel gears -- ISO system of accuracy 90.20 TC 60
ISO 18653:2003
Gears -- Evaluation of instruments for the measurement of individual gears 90.93 TC 60
ISO/TR 18792:2008
Lubrication of industrial gear drives 60.60 TC 60/SC 2
ISO 21771:2007
Gears -- Cylindrical involute gears and gear pairs -- Concepts and geometry 60.60 TC 60/SC 1
ISO/CD TR 22849
Bevel and hypoid gears -- Application and manufacturing recommendations 30.60 TC 60/SC 2
ISO/NP TR 23425
Example calculations for the load capacity of spur and helical gears according to ISO 6336 10.99 TC 60/SC 2
ISO 23509:2006
Bevel and hypoid gear geometry 60.60 TC 60/SC 2
95IEC/AWI 61400-4
Wind turbines -- Part 4: Design and specification of gearboxes 20.00 TC 60
ISO 81400-4:2005
Wind turbines -- Part 4: Design and specification of gearboxes 90.92 TC 60
ISO 81400-4:2005/Cor 1:2005
60.60 TC 60

21.220 Flexible drives and transmissions
ICS Field
21.220.01 Flexible drives and transmissions in general
21.220.10 Belt drives and their components
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 22:1991
Belt drives -- Flat transmission belts and corresponding pulleys -- Dimensions and tolerances 90.93 TC 41/SC 1
ISO 155:1998
Belt drives -- Pulleys -- Limiting values for adjustment of centres 90.60 TC 41/SC 1
ISO 254:1998
Belt drives -- Pulleys -- Quality, finish and balance 90.60 TC 41/SC 1
ISO 255:1990
Belt drives -- Pulleys for V-belts (system based on datum width) -- Geometrical inspection of grooves 90.93 TC 41/SC 1
ISO 1081:1995
Belt drives -- V-belts and V-ribbed belts, and corresponding grooved pulleys -- Vocabulary 90.93 TC 41/SC 1
ISO 1604:1989
Belt drives -- Endless wide V-belts for industrial speed-changers and groove profiles for corresponding pulleys 90.93 TC 41/SC 1
ISO 1813:1998
Belt drives -- V-ribbed belts, joined V-belts and V-belts including wide section belts and hexagonal belts -- Electrical conductivity of antistatic belts: Characteristics and methods of test 90.60 TC 41/SC 1
ISO 4183:1995
Belt drives -- Classical and narrow V-belts -- Grooved pulleys (system based on datum width) 90.93 TC 41/SC 1
ISO 4184:1992
Belt drives -- Classical and narrow V-belts -- Lengths in datum system 90.93 TC 41/SC 1
ISO 5288:2001
Synchronous belt drives -- Vocabulary 90.60 TC 41/SC 4
ISO 5290:2001
Belt drives -- Grooved pulleys for joined narrow V-belts -- Groove sections 9N/J, 15N/J and 25N/J (effective system) 90.93 TC 41/SC 1
ISO 5291:1993
Belt drives -- Grooved pulleys for joined classical V-belts -- Groove sections AJ, BJ, CJ and DJ (effective system) 90.60 TC 41/SC 1
ISO 5292:1995
Belt drives -- V-belts and V-ribbed belts -- Calculation of power ratings 90.60 TC 41/SC 1
ISO 5294:1989
Synchronous belt drives -- Pulleys 90.60 TC 41/SC 4
ISO 5295:1987
Synchronous belts -- Calculation of power rating and drive centre distance 90.60 TC 41/SC 4
ISO 5296-1:1989
Synchronous belt drives -- Belts -- Part 1: Pitch codes MXL, XL, L, H, XH and XXH -- Metric and inch dimensions 90.93 TC 41/SC 4
ISO 5296-2:1989
Synchronous belt drives -- Belts -- Part 2: Pitch codes MXL and XXL -- Metric dimensions 90.93 TC 41/SC 4
ISO 8370-1:1993
Belt drives -- Dynamic test to determine pitch zone location -- Part 1: V-belts 90.60 TC 41/SC 1
ISO 8370-2:1993
Belt drives -- Dynamic test to determine pitch zone location -- Part 2: V-ribbed belts 90.60 TC 41/SC 1
ISO 8419:2003
Belt drives -- Narrow V-belts -- Sections 9N/J, 15N/J and 25N/J (lengths in the effective system) 90.60 TC 41/SC 1
ISO 9563:1990
Belt drives -- Electrical conductivity of antistatic endless synchronous belts -- Characteristics and test method 90.92 TC 41/SC 4
ISO 9608:1994
V-belts -- Uniformity of belts -- Test method for determination of centre distance variation 90.93 TC 41/SC 1
ISO 9980:1990
Belt drives -- Grooved pulleys for V-belts (system based on effective width) -- Geometrical inspection of grooves 90.93 TC 41/SC 1
ISO 9982:1998
Belt drives -- Pulleys and V-ribbed belts for industrial applications -- PH, PJ, PK, PL and PM profiles: dimensions 90.60 TC 41/SC 1
ISO/DIS 12046
Synchronous belt drives -- Automotive belts -- Determination of physical properties 40.93 TC 41/SC 4
ISO 13050:1999
Curvilinear toothed synchronous belt drive systems 90.20 TC 41/SC 4

21.220.20 Cable or rope drives and their components
21.220.30 Chain drives and their components
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 487:1998
Steel roller chains, types S and C, attachments and sprockets 90.93 TC 100
ISO 606:2004
Short-pitch transmission precision roller and bush chains, attachments and associated chain sprockets 90.93 TC 100
ISO 606:2004/Cor 1:2006
60.60 TC 100
ISO 1275:2006
Double-pitch precision roller chains, attachments and associated chain sprockets for transmission and conveyors 60.60 TC 100
ISO 3512:1992
Heavy-duty cranked-link transmission chains 90.93 TC 100
ISO 4347:2004
Leaf chains, clevises and sheaves -- Dimensions, measuring forces and tensile strengths 90.92 TC 100
ISO 6971:2002
Cranked-link drag chains of welded construction, attachments and sprockets 90.93 TC 100
ISO 6972:2002
Cranked-link mill chains of welded construction, attachments and sprockets 90.93 TC 100
ISO 10823:2004
Guidelines for the selection of roller chain drives 90.93 TC 100
ISO 10823:2004/Cor 1:2008
60.60 TC 100
ISO 13203:2005
Chains, sprockets and accessories -- List of equivalent terms 90.93 TC 100
ISO 15654:2004
Fatigue test method for transmission precision roller chains 90.92 TC 100

21.220.99 Other flexible drives and transmissions

21.240 Rotary-reciprocating mechanisms and their parts
Including pistons, piston-rings, crankshafts, etc. for general engineering
Standards and projects under the direct responsibility of Secretariat
Standard and/or project TC
ISO 10816-6:1995
Mechanical vibration -- Evaluation of machine vibration by measurements on non-rotating parts -- Part 6: Reciprocating machines with power ratings above 100 kW 90.93 TC 108/SC 2

21.260 Lubrication systems
Lubricants, see 75.100


Any question, send the mail to findstandards@tom.com directly

http://www.findstandards.info

http://www.findstandards.info/Standards/DIN%20Standards.htm

http://www.findstandards.info/Standards/BSI%20Standards.htm

http://www.findstandards.info/Standards/ASTM%20Standards.htm

http://www.findstandards.info/Standards/ISO%20Standards.htm

http://www.findstandards.info/Standards/SAE%20Standards.htm

http://www.findstandards.info/Standards/JIS%20Standards.htm


http://www.findstandards.info/Standards/NFPA%20Standards.htm


http://www.findstandards.info/Standards/IEEE%20Standards.htm


http://www.findstandards.info/Standards/API%20Standards.htm

No comments:

Post a Comment